ECSA Calculator
ECSA is the area of an electrode that can take part in a reaction. Work it out from double-layer capacitance, ECSA = Cdl ÷ Cs, or from Hupd or CO stripping on platinum.
Keep the cathodic current negative, as your potentiostat shows it.
The numbers shown are made up. Use the current at one potential in a window with no reaction, with scan rates in mV/s.
40 is a common general value in alkaline solution. Use one measured for your material if you have it.
Electrochemically active surface area
- Double-layer capacitance
- 4.00 mF
- Per geometric area
- 4.00 mF/cm²
- Roughness factor
- 100
- R² of the fit
- 1.0000
This is an estimate. It is only as good as the Cs you chose.
The slope of this line is the double-layer capacitance.
The sums run on this page. Nothing you enter or paste is sent anywhere.
The formula
Charging current follows i = Cdl × ν, where ν is the scan rate, so a plot of charging current against scan rate is a straight line with a slope of Cdl. The tool takes half the gap between the anodic and cathodic currents as the charging current, which also removes any background they share.
Then ECSA = Cdl ÷ Cs, and the roughness factor is ECSA ÷ geometric area.
On platinum, ECSA = Q ÷ q, where Q is the charge after background correction and q is the charge for one monolayer: 210 µC/cm² for Hupd and 420 µC/cm² for CO stripping. Dividing by the mass of Pt gives m²/g.
Worked examples
A charging current of 0.4 mA at 100 mV/s is a capacitance of 4 mF, since 0.4 mA ÷ 0.1 V/s = 4 mF. With Cs = 40 µF/cm² that is an ECSA of 100 cm². On a 1 cm² electrode the roughness factor is 100.
On platinum, 0.5 mC of Hupd charge is 2.38 cm² of Pt, since 500 µC ÷ 210 µC/cm² = 2.38 cm². If the electrode holds 3.92 µg of Pt, that is 60.7 m²/g.
Common mistakes
- Plotting Δj against scan rate and forgetting that its slope is 2 × Cdl.
- Reading the current in a window where a reaction is running, which adds Faradaic current.
- Comparing ECSA between papers that used different values of Cs.
- Using Hupd or CO charge without subtracting the double-layer background.
Frequently asked questions
What is ECSA?
Electrochemically active surface area is the area of an electrode that can take part in a reaction. For a rough or porous catalyst it can be far larger than the geometric area you measure with a ruler.
How do I calculate ECSA from double-layer capacitance?
Run CVs at several scan rates in a potential window with no reaction. At one potential, take the charging current at each scan rate and plot it against the scan rate. The slope is the double-layer capacitance, Cdl. Then ECSA = Cdl ÷ Cs, where Cs is the specific capacitance of a flat surface of the material.
Which specific capacitance should I use?
There is no single right value. 40 µF/cm² is a common general value in alkaline solution, after McCrory et al. Values reported for metal oxides run from 22 to 130 µF/cm², and some studies consider 60 µF/cm² more realistic. Use a value measured on a flat surface of your material if you have one, and always state the value you used.
Why is the slope of Δj twice the capacitance?
Each branch of the CV carries a charging current of Cdl × scan rate, one positive and one negative. The gap between them is twice that, so a plot of Δj against scan rate has a slope of 2 × Cdl. Halve it, or the ECSA comes out double. The calculator does this for you if you choose Difference.
Can I trust ECSA from Cdl on oxides and hydroxides?
With care. There is no universally accepted specific capacitance for non-precious oxides and hydroxides. A material that does not conduct below the reaction onset, such as NiFe layered double hydroxide, can give a signal that mostly reflects its support. Pseudocapacitance can also inflate the result.
Should I use Hupd or CO stripping for platinum?
Both are standard. Hupd uses 210 µC/cm², and CO stripping uses 420 µC/cm², because oxidising CO takes two electrons. Either way, subtract the double-layer charge first: only the corrected charge relates to the surface area. A single value cannot represent every Pt surface, so alloys and shaped particles can differ.
How do I get charge from a CV?
Integrate the peak against potential, after subtracting the background, and divide by the scan rate. A peak area of 0.05 mA·V at 100 mV/s is 0.5 mC.
What is the roughness factor?
ECSA divided by the geometric area. A value of 100 means the electrode has 100 times more active surface than a perfectly flat one of the same size.
Sources
- McCrory, Jung, Peters and Jaramillo, Benchmarking Heterogeneous Electrocatalysts for the Oxygen Evolution Reaction, Journal of the American Chemical Society 135, 16977 (2013)
- Mygind, Rost and Escudero-Escribano, The Hidden Complexities of Electrochemically Active Surface Area Measurements, ACS Energy Letters 11, 2508 (2026)
- Xie et al., Capacitance Determination for the Evaluation of Electrochemically Active Surface Area in a Catalyst Layer of NiFe-Layered Double Hydroxides, Materials 17, 556 (2024)
Use this in your group?
Link to it from your lab’s resources page, or cite it like this:
METNMAT. ECSA Calculator. https://www.metnmat.com/tools/ecsa-calculator
For the experiment itself
See glassy carbon electrodes and platinum electrodes, or read how to calculate ECSA from double-layer capacitance and how to clean electrodes.
More free calculators
- Reference Electrode Potential Converter
Convert a potential from Ag/AgCl, SCE, Hg/HgO or Hg/Hg₂SO₄ to RHE and SHE.
- Faradaic Efficiency Calculator
Work out FE for several products at once, from GC, headspace or liquid data.
- Tafel Slope Calculator
Paste your polarization data for the Tafel slope, R², exchange current density and overpotential.