Skip to content
Guide

How to Store, Refill and Test a Reference Electrode

Store a reference electrode with its tip in the same solution it is filled with, never dry and never in deionised water. Refill it with fresh solution when the level drops or the reading drifts. To test it, measure the voltage between it and an unused electrode of the same type in the same solution: a healthy electrode reads within a few millivolts.

Filling and storage solutions by type

Use the filling solution the electrode was made for, because its strength sets the potential: Ag/AgCl sits at about +0.210 V vs SHE in 3 M KCl and +0.197 V in saturated KCl. For Hg/HgO, a filling solution that matches your cell's electrolyte keeps the junction potential small.

Usual filling and storage solutions for common reference electrodes
ElectrodeUsual filling solutionStore the tip inWatch for
Ag/AgCl3 M or saturated KClKCl of the same strengthChloride leaking into chloride-sensitive cells
Saturated calomel (SCE)Saturated KCl, with some crystals left undissolvedSaturated KClHeat, and the last crystals dissolving
Hg/HgOKOH or NaOH, often 1 MThe same alkali solutionCO₂ from air turning the alkali to carbonate
Hg/Hg₂SO₄Saturated K₂SO₄, or sulfuric acid in some designsThe same solutionChloride getting in
Ag/Ag⁺A silver salt such as AgNO₃ in an organic solvent, with a supporting electrolyteThe same solvent and saltWater, and slow drift

How to store a reference electrode

  • Keep the tip in a storage cap or bottle filled with the filling solution.
  • If it has a filling port, close it for storage and open it while you measure, so that the solution flows slowly out through the junction.
  • Never let the junction dry out, and top up the filling solution when the level drops.
  • Do not store it in deionised water, which draws the salt out of the junction and shifts the potential.
  • Do not store it in your cell's electrolyte, which can creep into the junction.
  • Keep calomel, Hg/HgO and Hg/Hg₂SO₄ electrodes away from heat, and dispose of them as mercury waste.

How to refill one

  • Draw out the old solution with a pipette or syringe.
  • Rinse the inside with a little fresh filling solution, and draw that out too.
  • Fill with fresh solution of the right strength, to just below the port.
  • Tap the body gently so that no air bubble stays near the element or the junction.
  • Rinse and wipe the outside, let it settle in its storage solution, then test it against your master electrode.

How to test a reference electrode

  • Keep one electrode of the same type unused, as a master, only for checking the others.
  • Put the master and the electrode under test side by side in the same solution, such as 3 M KCl for Ag/AgCl.
  • Measure the open-circuit voltage between them with a potentiostat or a high-impedance voltmeter.
  • A healthy electrode reads within a few millivolts of the master, often taken as within 5 mV. If it is further off or the reading wanders, refill it and test again. If it is still off, replace it.
  • To calibrate against RHE, bubble hydrogen through your electrolyte, run a slow cyclic voltammogram on a clean platinum electrode, and take the potential where the current crosses zero as 0 V vs RHE.
  • For Ag/Ag⁺ in organic solvents, add a little ferrocene at the end of the experiment and report potentials against the ferrocene/ferrocenium couple.

Why a reference electrode drifts

Common causes of reference electrode drift and what to do
CauseWhat you seeWhat to do
Old or diluted filling solutionA slow shift over days or weeksRefill with fresh solution
Blocked or dried junctionA noisy or unstable readingSoak the tip in filling solution for some hours, then test; replace it if it stays blocked
Air bubble at the tip or insideSudden jumps, or no readingTap the body to move the bubble, or refill
Contaminated filling solution or elementAn offset that stays after a refillReplace the electrode, and use a salt bridge if your electrolyte attacks it
Temperature changeA shift that follows the room or cell temperatureMeasure at a steady temperature and state it: table values are for 25 °C

Frequently asked questions

What solution should an Ag/AgCl reference electrode be stored in?

In KCl of the same strength as its filling solution, usually 3 M or saturated KCl. Never store it dry or in deionised water.

What is the filling solution of an Ag/AgCl reference electrode?

Potassium chloride, usually 3 M or saturated. Use the strength the electrode was made for, because it sets the potential: about +0.210 V vs SHE in 3 M KCl and +0.197 V in saturated KCl.

How do I check if a reference electrode is working?

Measure the voltage between it and an unused master electrode of the same type, both in the same solution. Within a few millivolts is healthy. A larger gap that stays after a refill, or a wandering reading, means it should be replaced.

Can a dried-out reference electrode be saved?

Often it can. Soak the tip in fresh filling solution for some hours, refill it, then test it against a master. If the reading is still off or unstable, replace it.

See also